By: Bridger Cottle, Owner/President of Drilling Fluids Solutions
Every driller who has ever tried to use a backreamer in clay knows that things can go south fast. Use the wrong type of reamer or try to rush your job and you end up with a balled-up reamer that feels like trying to pull a giant golf ball out through the hole.
Check out How to Properly Measure Your Reamer and Choose the Right Size for the Job to make sure you are using the right size reamer for your job.
99% of the time, problems when drilling in clay can be traced back to two things: using the wrong tool, or using the tool wrong. In this article, I’ll outline the tools and techniques you should be using to make sure you don’t get stuck in the mud. Or in this case, clay.
The right reamer
Clay has the smallest particle size of any soil type, so it tends to be dense. This density opens up a little when clay gets wet. Your backreamer should help to facilitate this. If you’re using the properly designed reamer, it should act like a giant blender when spinning at 120+ rpm. This spinning action intermingles the clay and the mud in your hole, creating a material with less density overall. Lower the density and you lower the risk of balling up.
Melfred Borzall’s Tornado reamer is great for clay. The shape, angle, and placement of the Tornado’s blades provide this blender-type action, with the added benefit of pumping the slurry to the back of the hole. As a result, the liquid is constantly being whisked in with your clay, so there’s less of a chance of the material hardening as you drill.
One of the biggest mistakes I’ve seen drillers make is trying to get away with using a reamer that isn’t specially designed to mix clay. They’ll say something like, “This is a small job, so let’s just use a 12-inch fluted reamer.” The problem is that a basic fluted reamer has more surface area, so there’s more for the clay to stick to. It lacks the blending action required to incorporate the clay into the mud.
Of course, even a great tool may not be the total solution all the time. Depending on the soil’s reactivity (that is, the plasticity of the clay), and the presence of contaminants like calcium, you’ll need to step up your game to increase slipperiness. That’s where the chemicals come in.
Soaps & detergent solutions
The go-to for many drillers is to throw more bentonite into the tank. But this would be a mistake because you’ll be adding clay to clay – and both want water. Detergents make “water wetter” by increasing the water’s surface tension. In turn, this allows the clay to absorb more water more easily, too. This is what you want, in order to help incorporate the clay into your fluid.
If you’re seeing clay come up across your shakers or clinging to your bit or backreamer, throw some specially formulated HDD detergent into your fluid tank. I recommend Melfred Borzall’s Drill Clean Plus™ or Cetco’s Drill-Terge™. These solutions are neither cationic or anionic (meaning no chemical charge), so they don’t interfere with any of the properties of the clay or your drill fluid. Always read the directions on the side of the jug, but a good rule of thumb is to add about a quart of solution per hundred gallons–or 2.5 gallons (½ a jug) to a thousand-gallon tank. Remember not to overdo it or your solution will get foam everywhere, making it a pain to clean up.
If soap doesn’t seem to be doing the trick and you’re still getting thick returns, your torque is going up, and things are starting to get a little scary, grab some Slik-Vis™, which is partially-hydrolyzed polyacrylamide (PHPA). This stuff is thick and looks a lot like Elmer’s glue, but it will jump your funnel viscosity fast. Since it’s like liquefied plastic, it forms a barrier that will prevent the clay in the ground from integrating with your mud. Add Slik-Vis in very small doses–about a pint or 8- to 16-oz. water bottle for every thousand gallons. Remember to always mix it in last. You don’t want it to strip out the bentonite that you’ve already added to the system.
How to know if you’re in clay
Always do viscosity tests on your returns. If you’re on a thousand-gallon tank and your returns are substantially thicker than the original fluid you were pumping, you know you’re in a clay situation. Returns that come back thinner indicate that you’re in some kind of groundwater or wet sand.
You’d also be surprised what you can tell simply from looking at your return mud and feeling it with your hands. Inspecting the chunks you find in this mud can give you a pretty accurate sense of the type of material you’re in, from clay to sand to shells.
One final trick is to grab a chunk of mud from your backreamer and roll it in your palms to make a little snake-like shape. If the “snake” holds together, it’s over 50% clay.
Clay situations can become worst-case-scenarios for drillers. It’s a material that just seems to complicate things quickly. But each of these challenges has a solution. With the right tools and the right additives, no clay will stand in your way.
About the Author
Bridger Cottle is the Owner and President of Drilling Fluids Solutions (DFS). DFS provides mud/slurry engineering, project design, mud training, and fluid program services for horizontal directional drilling, foundation drilling, direct pipe, slurry wall, microtunneling, and tunnel boring machine leaders. DFS is not associated with any particular mud or slurry brand, and has extensive experience with all major brands, providing education and expertise specific to each individual project.